How do I set the interface range in Juniper?

How do I set the interface range in Juniper?

List of Interface Range Commands in Juniper

1. 1 – Disable ports. # set interface interface-range SCOPE member-range ge-0/0/0 to ge-0/0/3. # set interface interface-range SCOPE disable.
2. 2 – Add vlan to ports. # set interfaces interface-range SCOPE unit 0 family ethernet-switching vlan members vlan20.

How do I enable interface in Juniper?

Enable/Disable Interface in Juniper

1. root@Juniper# set interfaces ge-0/0/1.0 disable << This is cisco equivalent of “shutdown”
2. root@Juniper# delete interfaces ge-0/0/1.0 disable << This is cisco equivalent of “no shutdown”
3. root@Juniper#show ge-0/0/1.0. root@Juniper# run show interfaces ge-0/0/1.0 terse.

What is em0 interface in Juniper?

em0 is the interface connected to the Ethernet switch on the local Switch Control Board (SCB).

How do I find my interface configuration in Juniper?

To display the current configuration for a Juniper Networks device, use the show command in configuration mode. This command displays the configuration at the current hierarchy level or at the specified level.

What is family INET in Juniper?

You use family inet to assign an IPv4 address. You use family inet6 to assign an IPv6 address. An interface can be configured with both an IPv4 and IPv6 address.

How do I set management interface on Juniper switch?

Configuring the In-Band Management Interface

1. Log in to the JCP CLI and enter configuration mode: root@host% cli root@host> configure.
2. Configure the IP address for the in-band management interface: root@host# set interfaces interface-name unit 0 family inet address address/prefix-length.
3. Configure VLAN tagging:

How do I set interface speed in Juniper?

Configure Interface Speed on Switches

1. In configuration mode, go to the [edit interfaces interface-name] hierarchy level. [edit ] user@host# edit interfaces interface-name.
2. To configure the speed, include the speed statement at the [edit interfaces interface-name ] hierarchy level.

What is PFE interface Juniper?

2 Packet Forwarding Engine (PFE) The PFE is the second basic component of the Juniper Networks router. It is the mass-transit system part of the router, so to speak. Whereas the routing engine is the brain of the router, the PFE tends to be more of a workhorse, carrying out the instructions it has been given.

What is an unnumbered interface?

An unnumbered interface does not have an IP address assigned to it. Unnumbered interfaces are often used in point-to-point connections where an IP address is not required. You can set up an unnumbered interface using the ip unnumbered command.

How many IP addresses can be configured on a given interface?

An interface can have one primary IP address and multiple secondary IP addresses. Packets generated by the Cisco IOS software always use the primary IP address. Therefore, all routers and access servers on a segment should share the same primary network number.

What is IP unnumbered interface?

Unnumbered interfaces are often used in point-to-point connections where an IP address is not required. You can set up an unnumbered interface using the ip unnumbered command. This command enables IP processing on an interface without assigning an explicit IP address to the interface.

How do you set up a zone in Juniper SRX?

Step-by-Step Procedure

1. Configure an Ethernet interface and assign an IPv4 address to it. [edit] user@host# set interfaces ge-0/0/1 unit 0 family inet address 203.0.113.1/24.
2. Configure an Ethernet interface and assign an IPv6 address to it.
3. Configure a security zone and assign it to an Ethernet interface.

What is network management interface?

Management interfaces allow network operators to manage the devices in their networks by providing access to each device’s control, configuration, and status information.

What is VME interface?

The Virtual Management Interface (VME) is automatically associated with the mgmt vlan. Users physically connect to the logical VME interface through the me0 ports within a VC. Here’s a sample capture to illustrate how this works: VME interface is configured: [edit interfaces]

Can you set a Fiber 10 Gigabit interface to half duplex?

Half-duplex is only for 10/100 Mbps. Fiber—1000 Mbps or 10 Gbps (full duplex). Half-duplex mode is not supported.

How do I check my juniper interface speed?

To view the speed configured for the interface, execute the show interfaces extensive command. The Speed Configuration field’s value of 1G or AUTO in the command output indicates whether the current operation speed of the interface is 1 Gbps or the default 10 Gbps, respectively.