What is the coefficient of friction for UHMW?
Table of Contents
What is the coefficient of friction for UHMW?
UHMW’s coefficient of friction is 0.14 or lower, and it typically does not require lubrica- tion.
What is the coefficient of friction for plastic?
| Coefficient of friction for a range of material combinations | ||
|---|---|---|
| combination | Static | Dynamic |
| rubber-metal | 1 | 0.5 |
| plastic-metal | 0.25…0.4 | 0.1…0.3 |
| plastic-plastic | 0.3-0.4 | 0.2…0.4 |
Is UHMW low friction?
UHMW (ultra high molecular weight polyethylene) is an extremely tough plastic with high abrasion and wear resistance. The versatility of polyethylene has made it a popular plastic for countless industrial applications that require durability, low friction, and chemical resistance.
How do you test UHMW?
Burn Test – light it with a match and smell the smoke. If it smells like candle wax – that indicates polyethylene. UHMW does not drip as readily as HDPE but it will drip. Oven Test – place it in an aluminum dish in a 300 degree oven.
What is stronger HDPE or UHMW?
About UHMW and HDPE UHMW has the highest impact strength of all the polyethylenes and the material will outwear carbon steel 10 to 1 in some applications. UHMW also has excellent resistance to stress and cracking, and the material has a low coefficient of friction (UHMW is self-lubricating).
What is the difference between UHMW and HDPE?
UHMW and HDPE are made from ethylene monomers. They are both thermoplastic polymers. They both have an indistinguishable appearance. The main difference between UHMW and HDPE is that UHMW contains long polymer chains with a very high molecular weight, whereas HDPE has a high strength to density ratio.
What is the coefficient of friction of polypropylene?
Static and kinetic friction coefficients of PP on PP under standard condition were 0.47±0.05 and 0.45±0.04, respectively.
What plastic has the lowest coefficient of friction?
PTFE
PTFE has the lowest recorded m value for any material with a dynamic coefficient of friction of between 0.05 and 0.15 and a static coefficient of friction of approximately 0.05. The other fluorocarbons i.e. FEP , PFA, ETFE and ECTFE all have extremely low coefficients of friction in the region of 0.14 to 0.25.
Is UHMW stronger than HDPE?
HDPE (High Density Polyethylene) has a somewhat lower tensile strength than UHMW. It possesses excellent chemical resistance and low moisture absorption.
What is the standard coefficient of friction?
8.4 Friction coefficient Most dry materials in combination have COF values between 0.3 and 0.6. Values outside this range are rare, but Teflon, for example, can have a coefficient lower than 0.04.
Is UHMW the same as Teflon?
UHMW has superior mechanical properties for wear, compressive strength, and impact resistance. Teflon is comparably soft and will creep due to its chemical structure. This results in rapid abrasion in dusty or gritty environments.
What is the most slippery plastic?
PTFE is the abbreviation for polytetrafluoroethene, a saturated fluorocarbon polymer, which was discovered serendipitously by Roy Plunkett, a 27-year-old research chemist working at the Du Pont Research Laboratories in Deepwater, New Jersey in 1938.
Which is better UHMW or HDPE?
HDPE is easy to fabricate and weld using thermoplastic welding equipment. It is an excellent choice for fabricated water tanks and chemical tanks. UHMW (ultra high molecular weight polyethylene) is an extremely tough, abrasion-resistant, low-cost plastic, used for a wide range of wear applications.
How is friction coefficient tested?
Test Procedure: A specimen is attached to a sled of specified weight. The sled is pulled across a second surface at a speed of 150 mm/minute. The force to get the sled started (static) and to maintain motion (kinetic) is measured.
Is HDPE the same as UHMW?
